P0705 Nissan Transmission Range Sensor Circuit Malfunction
Cost of diagnosing the P0705 TOYOTA code Labor: 1.0 The cost of diagnosing the P0705 TOYOTA code is 1.0 hour of labor. The auto repair's diagnosis time and labor rates vary by location, vehicle's make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
- The OBD2 Code Information Be Applicable For Nissan: 2013 Nissan Pathfinder,2013 Nissan Murano,2013 Nissan Juke Nismo,2013 Nissan GT-R,2013 Nissan Altima Sedan,2013 Nissan Almera,2013 Nissan 370Z,2012 Nissan Tiida,2012 Nissan Sunny,2012 Nissan Qashqai,2012 Nissan Murano,2012 Nissan Micra ELLE,2012 Nissan Micra DIG-S,2012 Nissan Maxima,2012 Nissan Juke Shiro,2012 Nissan GT-R,2012 Nissan.
- P0705 NISSAN Meaning The park/neutral position (PNP) switch includes a transmission range switch. The transmission range switch detects the selector lever position when the shift lever is in the N or P shift position and sends a signal to the Transmission Control Module (TCM).
- P0705 TRANSMISSION RANGE SENSOR A. Turn ignition switch ON. Check voltage between TCM harness connector terminal and ground. Is the inspection result normal? YES GO TO 10. NO Repair or replace malfunctioning parts. CHECK N POSITION SW CIRCUIT (PART 1) 1. Turn ignition switch OFF. Disconnect TCM connector.
- Nissan Rogue Service Manual: P0705 transmission range sensor A. P0705: T/M RANGE SENSOR A Transmission Range Sensor A Circuit (PRNDL Input) When all of the following conditions are satisfied and this state is maintained for 2 seconds: Two or more.
– Misadjusted Park/Neutral Position Switch
– Park/Neutral Position Switch harness is open or shorted
– Park/Neutral Position Switch circuit poor electrical connection
The park/neutral position (PNP) switch includes a transmission range switch. The transmission range switch detects the selector lever position when the shift lever is in the N or P shift position and sends a signal to the Transmission Control Module (TCM).
Description
• The PNP switch is included in the control valve assembly.
• The PNP switch includes 4 transmission position switches.
• TCM judges the selector lever position by the PNP switch signal.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION: Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.CHECK DTC DETECTION
1. Turn ignition switch ON.
2. Select “DATA MONITOR”.
3. Start engine.
4. Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.
Follow the procedure “With CONSULT-III”.
Is “P0705 PNP SW/CIRC” detected? YES >> Go to TM-129, 'Diagnosis Procedure'.
NO >> Check intermittent incident. Refer to GI-42, 'Intermittent Incident'.
Diagnosis Procedure
1.CHECK CVT POSITION
1. Disconnect CVT unit harness connector.
2. Remove control cable from manual lever. Refer to TM-256, 'Exploded View'.
3. Check PNP switch. Refer to TM-130, 'Component Inspection'.
Is the inspection result normal? YES >> Adjust CVT position. Refer to TM-253, 'Inspection and Adjustment'.
NO >> GO TO 2.
2. CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector.
3. Check continuity between TCM harness connector F16 (A) terminal 1, 2, 3, 4, 11 and CVT unit harness connector F46 (B) terminal 5, 14, 15, 18, 4.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace damaged parts.
3. CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 2)
Check continuity between TCM harness connector F16 terminal 1, 2, 3, 4, 11 and ground.
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace damaged parts.
4.DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal? YES >> Replace the TCM. Refer to TM-254, 'Exploded View'.
NO >> Repair or replace damaged parts.
Component Inspection
P0705 Nissan
1.CHECK PNP SWITCH
Check the continuity of the PNP switch by changing selector lever to various positions and checking continuity between CVT unit terminals and ground.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace transaxle assembly. Refer to TM-259, 'Exploded View'.
P0703 stop lamp switch
Description BCM detects ON/OFF state of the stop lamp switch and transmits the data to the TCM via CAN communication by converting the data to a signal. DTC Logic DTC DETECTION LOGIC DTC CON ...
P0710 cvt fluid temperature sensor
Description The CVT fluid temperature sensor detects the CVT fluid temperature and sends a signal to the TCM. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive v ...2014 Nissan Sentra P0705
Other materials:
Precaution
Supplemental Restraint System (SRS) 'AIR B AG' and 'SEAT BELT PRE-TENSIONER' The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front ...
P0705 Nissan Maxima
P0128 Thermostat function
DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0128 is displayed with DTC P0300, P0301, P0302, P0303, P0304, P0305 or P0306, first perform the trouble diagnosis for DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306. Refer to EC-1283, 'DTC Logic'. Engine coolant temperature has n ...
P0705 Nissan Almera
Precautions on cruise control
1. CANCEL switch 2. ACCEL/RES switch 3. COAST/SET switch 4. ON/OFF switch ● If the cruise control system malfunctions, it cancels automatically. The SET indicator light in the instrument panel then blinks to warn the driver. ● If the SET indicator light blinks, turn the cruise ...